英文翻译

3.23 LUBRICATION
3.23.1 Oil lubrication shall be provided for enclosed gear trains and speed reducers in accordance with section3.14 .
3.23.2 Lubrication of other mechanical operating parts shall be means of a high pressure gun . Buttonhead type grease fittings made of brass , monel or stainless steel shall be used throughout . This requirement does not apply to bearings where overgreasing can damage the equipment , such as an electric motor . Special lubrication fittings shall be used in these case that can be accessed only by specially trained personnel with the proper lubrication equipment .
3.23.3 Electrical motors shall include automatic lubrication with pressurized ( and drained) Simalube type grease tank at each fitting. Gantry motors bearings shall be sealed type whenever possible. Hoist, trolley and boom main motors , as well as hydraulic systems , should be greasable as described above .
3.23.4 The lubricating fittings of journals or bearings shall be readily accessible . Grease fittings shall be gathered at the same place as much as possible by means of stainless steel tubing for convenient lubrication .
3.23.5 Only one size and type of lubricating fitting shall be used except for special equipment as allowd by 3.23.2 above .All fittings shall be plainly visible and accessible .
3.23.6 The Contractor shall furnish and install lubricants and hydraulic fluid in sufficient quantities for initial lubrication of the crane .
3.23.7 The crane shall be lubricated with product of either mobil or shell .
3.23.8 Oil samples shall be taken from each reducer and hydraulic power uint during field testing . See section 9 .
3.23.9 The Contractor shall provide at crane acceptance a listing of all lubricants installed in the crane .

10.3 AUTOMATIC LUBRICTION SYSTEM
10.3.1 If this technical option is exercised , a centralized automatic grease lubrication system(s) shall be supplied at the gantry level with the exception of motors and couplings .
10.3.2 The system shall have the following feature :
Dual line
Electric pump
High/Low pressure alarms tied into the CMS
Manual adjustment of individual lubrication supply rates of each supply point
Stainless steel distribution lines and manifold blocks
Reservoir fill point accessible from ground level
Tank level full/empty signal light next to fill point and tied into the CMS
Sufficient resevior size to minimize refilling frequency
10.3.3 The Bidder’s Proposal shall contain a full description of the system offered .
10.3.4 The system shall be subject to the Engineer’s approval .
麻烦各位大虾帮助小弟翻译一下这篇关于干油润滑的文章,时间紧急!多谢大虾们!

3.23 LUBRICATION
3.23.1 Oil lubrication shall be provided for enclosed gear trains and speed reducers in accordance with section3.14 .
3.23 润滑
3.23.1给闭合齿轮传动链和减速机做油润滑须依照3.14章节来进行。

3.23.2 Lubrication of other mechanical operating parts shall be means of a high pressure gun . Buttonhead type grease fittings made of brass , monel or stainless steel shall be used throughout . This requirement does not apply to bearings where overgreasing can damage the equipment , such as an electric motor . Special lubrication fittings shall be used in these case that can be accessed only by specially trained personnel with the proper lubrication equipment .
3.23.2 其他机械操作部件的润滑须使用高压油枪。应始终使用黄铜、锰合金或不锈钢制成的扁圆头类型的黄油嘴。这些要求不适用于油脂过多会损坏设备的轴承，比如电动机。特殊的润滑配件要在下列情况中使用，即只能由专业受过培训的人员使用恰当的润滑装备完成的情况。

3.23.3 Electrical motors shall include automatic lubrication with pressurized ( and drained) Simalube type grease tank at each fitting. Gantry motors bearings shall be sealed type whenever possible. Hoist, trolley and boom main motors , as well as hydraulic systems , should be greasable as described above .
3.23.3 电动机应包含自动润滑，使用每个配件上耐压的（及泄油的）Simalube类型的油槽。吊架电机轴承应尽可能是均密封类型的。提升电机、台车电机和主电机及液压系统，应如上所述来润滑。

3.23.4 The lubricating fittings of journals or bearings shall be readily accessible . Grease fittings shall be gathered at the same place as much as possible by means of stainless steel tubing for convenient lubrication .
3.23.4 轴颈或轴承的润滑配件应容易获得。为了方便润滑，应用不锈钢管尽可能把黄油嘴聚拢在同一个地方。

3.23.5 Only one size and type of lubricating fitting shall be used except for special equipment as allowd by 3.23.2 above .All fittings shall be plainly visible and accessible .
3.23.5 只使用一种尺寸和类型的润滑装置，除了上面的3.23.2章节所允许的特殊设备。所有这些配件应清楚易见并易于获得。

3.23.6 The Contractor shall furnish and install lubricants and hydraulic fluid in sufficient quantities for initial lubrication of the crane .
3.23.6 承包人要为吊车最初的润滑供给并加注入足够数量的润滑油和液压油。

3.23.7 The crane shall be lubricated with product of either mobil or shell .
3.23.7 吊车润滑要使用美孚公司或壳牌石油公司的产品。

3.23.8 Oil samples shall be taken from each reducer and hydraulic power uint during field testing . See section 9 .
在实地测试期间，油样要从每个减速机和液压动力单元中提取。参见第9章节。

3.23.9 The Contractor shall provide at crane acceptance a listing of all lubricants installed in the crane .
承包人要在起重机验收中提供所有注入起重机上的润滑油的清单。

10.3 AUTOMATIC LUBRICTION SYSTEM
10.3.1 If this technical option is exercised , a centralized automatic grease lubrication system(s) shall be supplied at the gantry level with the exception of motors and couplings .
10.3自动润滑系统
10.3.1如果执行这些技术附件，应在吊架水平位置提供一个集中自动油脂润滑系统，电机和连接件除外。

10.3.2 The system shall have the following feature :
Dual line
Electric pump
High/Low pressure alarms tied into the CMS
Manual adjustment of individual lubrication supply rates of each supply point
Stainless steel distribution lines and manifold blocks
Reservoir fill point accessible from ground level
Tank level full/empty signal light next to fill point and tied into the CMS
Sufficient resevior size to minimize refilling frequency
10.3.2该系统有下列特征：
双路
电泵
嵌入CMS系统的高/低压报警
手动调节每个注油点各自的润滑油注入速率
不锈钢分布线和油路块（或称为歧管挡块）
储油箱注油点从地准水平面获取
油箱液位满/空信号灯紧邻注油点并嵌入CMS系统
充裕的储油箱尺寸以使重注油频率减到最小

10.3.3 The Bidder’s Proposal shall contain a full description of the system offered .
投标人的提案应包含关于所供应系统的详尽描述。

10.3.4 The system shall be subject to the Engineer’s approval .
该系统将取决于工程师的认可。

注：
3.23.3处：
Simalube是瑞士的一家注油器等产品的生产商。
Hoist, trolley and boom main motors因不是很熟悉你这种起重机，故此处这几个电机用途不是特别明白。应根据你的设备来定名。
10.3.2处：
CMS：照文章中看来，应该是计算机监控系统，或之类的控制系统。

这段文章应该是取自起重机采购协议或合同中关于润滑的部分章节，大体意思应该差不多。你再参照你熟悉的设备来进行小幅修改即可。

段落不算短啊，应该多加分才是的哦:)

温馨提示：内容为网友见解，仅供参考

当前网址：https://11.t2y.org/zz/vmsf4qv8.html